exercises:2014_ethz_mmm:infra_red

In this exercise we will compare the vibrational spectrum of two molecules (methanol and benzene) computed with a static method (diagonalization of the dynamical matrix) and with molecular dynamics. The spectra for methanol are available in this paper 10.1039/c3cp44302g. As in the last lectures, to make this exercise computationally feasible, we will use for MD the efficient Density Functional based Tight Binding (DFTB) method. It requires only a minima basis, but delivers nevertheless reasonable results due to an empirical correction term called *repulsion potential*.

You should run these calculations on 16 nodes with **commented** files from the wiki exercise_10.1.tar.gz.

`bsub -n 16`

, particularly the vibrational spectrum.
Download, as usual, the
To compute the vibrational spectra, we need to first find a minimum structure for the systems. To this end, we use the input files ** optc6h6.inp ** and **optmet.inp**. These runs are still done with DFT (not DFTB). The last geometry from the ** C6H6-pos.1.xyz ** is the optimized one. Copy it to optc6h6.xyz. This will be the input for the ** vibc6h6.inp ** which computes the spectra, by adding a new section in the input:

&VIBRATIONAL_ANALYSIS INTENSITIES NPROC_REP 32 DX 0.001 &PRINT &PROGRAM_RUN_INFO ON &END &END &END

The ** .mol ** file for c6h6 is already there, since the job is quite long. However, if you plan to run it (maybe after the methanol case) remember to add the option to ask for more wallclock time ** -W HH:MM ** to bsub.

NPROC_REP has to be the same number of processors as in the bsub!! Edit the input!!

For the intensities, the derivative of the dipole along the normal modes is necessary (see lecture). So the moments are computed in the standard non periodic fashion:

&DFT BASIS_SET_FILE_NAME ./BASIS_MOLOPT POTENTIAL_FILE_NAME ./GTH_POTENTIALS &PRINT &MOMENTS PERIODIC FALSE &END &END

This code will generate frequencies and intensities of the IR spectrum in the files ** C6H6-VIBRATIONS.mol ** and the same for methanol.
This file can be read by the visualization program ** molden **.

- $ module load molden
- $ molden C6H6-VIBRATIONS.mol
- Use the “normal mode” check in the graphical interface. The spectrum appears.

- Compare the one of methanol with experiments (see paper) and the one of benzene with literature on the internet.
- Which kind of modes will correspond to stretching of CH and CC bonds?
- Try to animate some frequencies, and report the kind of mode corresponding to all peaks.

Download the following file into your project directory:

You can unpack it with the following command:

$ tar -xvzf dftb_params.tgz

You will find a fortran program in the repository, called ** dipole_correlation.f90 **
Compile it (module load gcc; gfortran -o dipole.x dipole_correlation.f90 ). This program computes the correlation function of the (derivative of) the dipole moment, and performs also the Fourier transform.

Run ** cp2k ** with the ** md*.inp ** input files (for the two molecules). Note that the dipole moment and derivatives are extracted from simulation and saved in a file dip*traj (check the input). Run first 5000 steps, then edit the file dipole.in and run ** dipole.x < dipole.in **.
This will generate the autocorrelation function of the dipole derivative (why?) and its Fourier transform (frequency domain).

- Check the result. Is it satisfactory with respect to the DFT static calculation and literature? Why?

- Run 40000 more steps. Check the new results. Discuss what you obtained. Discuss the behavior of the autocorrelation in the time domain.

exercises/2014_ethz_mmm/infra_red.txt · Last modified: 2014/10/15 14:23 by oschuett

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-ShareAlike 4.0 International